Thanks for visiting our site!
Acetylene Cutting
Checkout Ebay Auctions For The Cheapest Prices
 |
 OXY ACETYLENE WELDING GAS CUTTING OUTFIT TORCH SET KIT  US $149.99
|
 Welding Torch Kit Oxy-Acetylene Cutting Kit Oxygen US $109.95
|
 Goss 240 Oxy acetylene cutting torch US $25.00
|
 Spare Parts Welding Acetylene Gas Cutting Torch Nozzle Tip G02-2 US $11.67
|
 Pro rrbbb CUTTING TORCH KIT OXY ACETYLENE WELDING VICTOR TYPE US $144.99
|
| Powered by phpBay Pro |
Also Checkout Amazon For Related Products:
| Account limit of 2000 requests per hour exceeded. |
Here are some more information for Acetylene Cutting:
As we already know to start a car engine: the car key should be inserted in the ignition part to start the engine. However, there are times when the engine would not start due to temporary negative feedback from the wiring systems or the car has not been used for quite some time. When this occurred, the best suggestion is to use the direct connection wiring from battery to starter body to start the engine. Normally if the battery is in full charged, single direct connection should be just enough to make the engine crank and start. In order to do that, important tools below are required to perform the task.
The followings are the tools that are required in performing the above task:
1. A meter and a half long color wire (i.e. black or red)
2. A battery clip.
3. A wire cutter.
To prevent your car wiring from being damaged completely after doing the task, you need to be very careful on the mentioned steps as below:
a) Cut the wire end
b) The battery is charged and the car key is at the ON sign
c) Connect the red wire using the battery clip to the (+) battery.
d) Touch the red wire end to the car starter connector several times in order to confirm the car to start.
Once you hear the engine start, stop touching the red wire end to the car starter to prevent the damage of the whole wiring system. Seek for assistance if you have any difficulties. Follow the mentioned steps to protect the wiring from being damaged completely.
The author is an automotive entrepreneur who had been in engineering industry for more than 15 years and has had extra experience practically in some engineering machine such as acetylene welding and electrical cutting machine.
Visit his blog to get more useful solutions to basic car problems of your car at http://membaikikenderaananda.blogspot.com.
How to Keep yourself Safe While Welding
Welding is a rewarding practice which requires proper training and safety procedures to be followed in order to keep everyone safe. This process may also be referred to as "Oxy-welding and cutting" and as the name implies the machines employed in this process use oxygen and fuels in order to produce intense heat which is capable of cutting extremely hard metals. The main fuel used to power these machines is called "Acetylene".
When the main fuel (acetylene) is burned and mixed with oxygen it can produce extreme temperatures, they usually range between 3200 and 3500 Celsius which is the equivalent of 5800-6300 Fahrenheit; with such extreme temperatures it goes without saying that proper safety precautions must be taken in order to keep yourself and those surrounding you safe. Since the fuels used to weld are extremely flammable, they should be kept in rooms with controlled temperature and in some cases pressure.
Other fuels used to weld and cut metals are: gasoline, hydrogen, methylacetylene-propadiene or MAPP gas, propane and propylene. Depending on the type of job a different type of fuel must be used, for instance underwater welding has to be done using hydrogen as the main fuel since acetylene becomes very unstable at 33 feet.
Before welding you must always check the equipment for leaks or malfunctions, you should also wear protective goggles or special masks which will cover your eyes and prevent the intense radiation from causing them harm, special gloves and even still toe boots should be used while welding.
You must also learn to identify the functions of the welding machine as well as the types of torches used for different tasks, some of the torch types are:
Welding Torch: its function is to melt and weld metals, it has two pipes and no oxygen-blast trigger.
The Rose-bud Torch: this name was given to it because the end of the flame looks like a rose-bud, it is used to heat metals and reshape them instead of melting the substance or cutting it.
Injector Torch: these torches have a small head which injects oxygen and relies on the Venturi effect to drag fuel gas along with it.
Cutting Torch: has three pipes one of which carries oxygen which can be adjusted through the oxygen-blast trigger, the main purpose of this torch is to cut metals.
Different torch types must be used according to the task, however the safety procedures remain the same, so remember to wear protective equipment, use respirators to avoid inhaling hazardous fumes produced by chemical reactions of the fuel and the burning metal and run a thorough assessment about your surroundings and the risk of fire.
About the Author
I Howd - How to Articles offers a great variety of do-it-yourself guides which provide useful information. Learn how to weld and keep yourself safe while doing it, visit us today!
Where can i buy a bottle of Acetylene for my gas cutter?
I found gas cutting gear in my shed, and im in need of gas for it. can any one tell me where to get the bottles; oxygen and Acetylene. am in england.
as far a I know you can't "buy" gas bottles - you have to take out a rental contract for the use of the bottles, then pay for the initial and subsequent refills.
The most widely available is BOC (British Oxygen Company) and you will find a local bottle depot either via the net or yellow pages or similar. To open an account you have to provide your bank details so they can set up a direct debit mandate to take the initial payment and then the future yearly bottle rental charges. If you wish, after the initial sign up you can pay for the gas by cash or card if you prefer.
Oh yes, a tip: if possible change both bottles at the same time (even if the oxy has not run out) as there is a handling charge for their collection and delivery (to their depot), cleaning, refilling and safety checking. And if you do one on it's own **** law will happen and the other will run out the following week!
Another supplier is Air Products - but they appear to charge more.
Hope this helps
Tom Warren was Plainview's man of steel
Tom Warren was a man of steel — in more ways than one.
Thanks for visiting!
