Energy Products

The Milwaukee Valve BB2-100 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has female NPT threaded connections on both ends that create tighter seals than straight threads. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use in applications including natural gas and liquid propane shutoff, fuel oil and oil systems, HVAC, and both liquid and vacuum service. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-100 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has female NPT threaded connections on both ends that create tighter seals than straight threads. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use in applications including natural gas and liquid propane shutoff, fuel oil and oil systems, HVAC, and both liquid and vacuum service. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

This cast iron Milwaukee Valve CW223E series wafer-style butterfly valve has ethylene propylene diene monomer (EPDM) seats and seals, an aluminum-bronze disc, a lever handle, and flanged connections. Made of cast iron for higher corrosion resistance than steel, this wafer-style valve fits between two pipe flanges and is designed to retain a seal against two-way pressure to prevent backflow in single-direction systems. It has EPDM seats and seals to provide increased water and chemical resistance, and the ductile-iron lever handle provides manual flow control. The disc is made of aluminum bronze, which has better corrosion resistance than stainless steel. The maximum pressure is 200 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is -30 to 250 degrees F. This valve has flanged connections for bolting to pipes for greater ease in installation and maintenance than welded connections. It meets Manufacturers Standardization Society (MSS) SP-67 and American Petroleum Institute (API) 609 standards for quality assurance, and the United States Coast Guard approves it for use in Category A service. This butterfly valve is for use in applications including agricultural and turf irrigation, food and beverage industry, pulp and paper industry, oil and gas systems, chemical plants, wastewater treatment, and water distribution. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-350 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and solder connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has solder end connections for a semi-permanent yet reversible connection to tubing. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use with gas, air, and oil systems, and both liquid and vacuum service applications. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-350 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and solder connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has solder end connections for a semi-permanent yet reversible connection to tubing. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use with gas, air, and oil systems, and both liquid and vacuum service applications. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve CL323E series lug-style butterfly valve with a gear operator is made of cast iron and has ethylene propylene diene monomer (EPDM) seats and seals, an aluminum-bronze disc, and flanged connections. This lug-style valve is secured between two pipe flanges by a separate set of threaded bolts for each flange and is suitable for end-of-line service and removal or replacement of downstream piping. The cast-iron gear operator with a handwheel rotates the disc in the valve seat to fully open, regulate, or stop flow through the valve and has an indicator dial that displays the position of the disc in the valve. The disc is made of aluminum bronze, which has better corrosion resistance than stainless steel, and the EPDM rubber seats and seals provide increased water and chemical resistance. The maximum pressure for bidirectional dead-end service is 200 pounds per square inch (psi), and the working temperature range is -30 to 250 degrees F. This valve has flanged connections surrounding the body on both sides for bolting to pipes and for greater ease in installation and maintenance than welded connections. The valve meets Manufacturers Standardization Society (MSS) SP-67 and American Petroleum Institute (API) 609 standards for quality assurance, and the United States Coast Guard approves it for use in Category A service. This valve is for use in applications including agricultural and turf irrigation, food and beverage industry, pulp and paper industry, oil and gas systems, chemical plants, wastewater treatment, and water distribution. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-350 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and solder connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has solder end connections for a semi-permanent yet reversible connection to tubing. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use with gas, air, and oil systems, and both liquid and vacuum service applications. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-102 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle with memory stop, and female National Pipe Taper (NPT) threaded connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has female NPT threaded connections on both ends that create tighter seals than straight threads. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. The lever comes with a memory stop feature for adjusting the valve opening to a preset position. This valve is for use in applications including natural gas and liquid propane shutoff, fuel oil and oil systems, HVAC, and both liquid and vacuum service. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-350 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle and solder connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has solder end connections for a semi-permanent yet reversible connection to tubing. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. This valve is for use with gas, air, and oil systems, and both liquid and vacuum service applications. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.

The Milwaukee Valve BB2-102 series unibody butterfly valve is made of bronze with a stainless steel 304 disc, and it has a lever handle with memory stop, and female National Pipe Taper (NPT) threaded connections on both ends. This bronze valve, which is higher strength and more corrosion resistant than brass, is full port for reduced friction; its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The one-piece construction reduces the possibility of leakage and it has female NPT threaded connections on both ends that create tighter seals than straight threads. The maximum pressure is 175 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 275 degrees F. The zinc-plated steel lever handle with a vinyl sleeve rotates the stainless steel 304 disc in the valve seat to fully open, throttle, or stop flow through the valve. The lever comes with a memory stop feature for adjusting the valve opening to a preset position. This valve is for use in applications including natural gas and liquid propane shutoff, fuel oil and oil systems, HVAC, and both liquid and vacuum service. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. The Milwaukee Valve Company manufactures manual and actuated valves, controls, and control accessories. The company, founded in 1901, and headquartered in New Berlin, WI, meets International Organization for Standardization (ISO) 9001:2008 and 14001:2004 standards.