Thanks for visiting our site!
Hypertherm Powermax
Checkout Ebay Auctions For The Cheapest Prices
 |
 Hypertherm Powermax-900 Plasma Cutter  US $605.00
|
 Hypertherm powermax30 plasma cutter 220478 220480 20pcs US $54.00
|
 Hypertherm Powermax 65 Plasma Cutter 083270 US $2,325.00
|
 Hypertherm Powermax 65 Ohmic Shield 220948 US $10.20
|
 Hypertherm Powermax 30 Nozzles 220480 US $12.40
|
 Hypertherm Electrode 120473 Powermax MAX-100 Plasma Cutting Torch 1 Piece NEW US $.99
|
 Hypertherm Powermax 65 & 85 - 65 Amp Nozzles 220819 5pk US $24.95
|
 Hypertherm Powermax 600 Electrodes 120573 US $34.15
|
 Hypertherm Powermax 1650 Electrodes 120926 US $32.25
|
 Five Hypertherm Nozzles Powermax 600 40 A PMX 120826 US $44.99
|
 Hypertherm Powermax-1100 Air Electrode 120473; 5 pack US $28.65
|
| Powered by phpBay Pro |
Also Checkout Amazon For Related Products:
| Account limit of 2000 requests per hour exceeded. |
Here are some more information for Hypertherm Powermax:
The Plasma Cutter is a GREAT tool to allow you to perform fast & precise cuts in all metals used in welding. Since the 1990's, it has become affordable to many home users. But the Plasma Cutter is still pretty spendy for most of us. Here's the "deal":
1) Plasma Cutters cut virtually anything put in it's path.
2) They produce CLEAN & PRECISE cuts
3) They can be about 10 times faster than Oxy-Acet. to cut ferrous metals.
4) They also cut STAINLESS!
But be CAREFUL!
1) You're dealing with VERY high temperatures!
2) The voltages at the working area are higher.
3) For heavier duty units the noise level is enough to need ear-plugs.
4) Wear ALL appropriate safety gear: gloves, goggles, etc.
The "What's it" part:
The Plasma "state of matter" happens when a gas is super-heated via an arc. When driven through the arc under pressure, it becomes "plasma", & cuts metals like butter. Different gases may be used (including air), depending on what you're cutting.
"The bottom line":
1) If you HAVE the money & you will be doing LOT'S of cutting....
2) AND you NEED very clean and precise cuts...Then GET ONE!
3) BUT remember that MOST beginning & some advanced welders can't justify the expense, NOR do they NEED one. (at least in the beginning).
Below are some comments about some of the Cutters that are available:
It's your call, to buy or not to buy:
* As a beginner, it could probably wait.
* If you have the money & KNOW that you would eventually get one, then GET ONE NOW.
* In my recent search, the cheapest used one I saw on Craigslist was $700 ($1400 new)(Hypertherm Powermax 600).
* New Miller model 375 = $1400, to Miller model 1251 = $4800 (Cuts to 1 1/4").(via weldersource.com).
* Plus a new "Giant Tech 50D" at $465 on sale.(at plasmametalcutter.com).
Shop around, ask your buddies, then get one for YOUR needs and budget!
HAPPY CUTTING!
I started working as a Journey-level welder for Weyerheauser Timber Company more than 20 years ago. That was the same year that I became a certified welder in Washington State. I weld today because it's cool & interesting! If you can DREAM it, you can probably WELD it! My website: http://www.arc-welding-and-beyond.com The purpose of my website is to educate the beginning welder in ALL RELATED skill areas of welding: running great beads, designing, preparing, layout, finishing, & troubleshooting problems. "Welding is more than just running beads!"
Plasma Cutter - Are You Ready For One? - I'll Help You Decide
The Plasma Cutter is a GREAT tool to allow you to perform fast & precise cuts in all metals used in welding. Since the 1990's, it has become affordable to many home users. But the Plasma Cutter is still pretty spendy for most of us. Here's the "deal":
1) Plasma Cutters cut virtually anything put in it's path.
2) They produce CLEAN & PRECISE cuts
3) They can be about 10 times faster than Oxy-Acet. to cut ferrous metals.
4) They also cut STAINLESS!
But be CAREFUL!
1) You're dealing with VERY high temperatures!
2) The voltages at the working area are higher.
3) For heavier duty units the noise level is enough to need ear-plugs.
4) Wear ALL appropriate safety gear: gloves, goggles, etc.
The "What's it" part:
The Plasma "state of matter" happens when a gas is super-heated via an arc. When driven through the arc under pressure, it becomes "plasma", & cuts metals like butter. Different gases may be used (including air), depending on what you're cutting.
"The bottom line":
1) If you HAVE the money & you will be doing LOT'S of cutting....
2) AND you NEED very clean and precise cuts...Then GET ONE!
3) BUT remember that MOST beginning & some advanced welders can't justify the expense, NOR do they NEED one. (at least in the beginning).
Below are some comments about some of the Cutters that are available:
It's your call, to buy or not to buy:
* As a beginner, it could probably wait.
* If you have the money & KNOW that you would eventually get one, then GET ONE NOW.
* In my recent search, the cheapest used one I saw on Craigslist was $700 ($1400 new)(Hypertherm Powermax 600).
* From a new Miller model 375 = $1400, to a Miller model 1251 = $4800 (Cuts to 1 1/4").(via weldersource.com).
* Plus a new "Giant Tech 50D" at $465 on sale.(at plasmametalcutter.com).
Shop around, ask your buddies, then get one for YOUR needs and budget!
HAPPY CUTTING!
About the Author
I started working as a Journey-level welder for Weyerheauser Timber Company more than 20 years ago. That was the same year that I became a certified welder in Washington State. I weld today because it's cool & interesting! If you can DREAM it, you can probably WELD it!
My website: http://www.arc-welding-and-beyond.com
The purpose of my website is to educate the beginning welder in ALL RELATED skill areas of welding: running great beads, designing, preparing, layout, finishing, & troubleshooting problems. "Welding is more than just running beads!"
Advanced Machine Tools Spring Open House
Advanced Machine Tools (AMT) announced today that it is opening its doors for open house events at its Georgia and North Carolina Technology Centers
Thanks for visiting!
