Energy Products

These meters measure flow via pressure drop across a laminar flow element (LFE). Because the flow element makes the flow stream laminar, placement in the process does not require straight pipe runs upstream or downstream of the meter, greatly simplifying installation. The LFEs also provide an outstanding turndown ratio of 100:1 giving the meter a very broad and accurate measuring range. As compared to thermal mass technologies, the LFE design provides an ultrafast response at start-up or input change, often within 20 milliseconds; there is also no thermal drift with this technology. An integrated keypad around the display is all that is required to program the unit for service-no additional costs for programming modules. The 0 to 5 VDC output allows transmission of the flow value to a remote display, recorder, or controller regulating a valve or pump. For portable flow metering applications, order the battery pack listed below. Units can be mounted via threaded taps in the meter body. Flowmeters include the integrated sensor, display, and transmitter. All models include a 120 VAC power adapter; 220 VAC European adapters. Meters feature dynamic display that simultaneously shows flow rate, line pressure, fluid temperature. For the unit shown, both power and input/output signals are transmitted through a single multi-pin connector.

These controllers feature an advanced straight-tube sensor that ensures accurate and repeatable results. Gas flow measurements are unaffected by moderate temperature and pressure variations at the inlet. The meter also allows a four-point calibration across the flow range to improve meter linearity. The flow rate set point can be established by either a local potentiometer or by a remote 4 to 20 mA or 0 to 5 VDC signal. Output data is sent via a 0 to 5 VDC or 4 to 20 mA signal; an analog-to-RS converter is also available for data collection and analysis on your PC. All controllers include a detachable 31/2-digit LCD that can be tilted up to 90° for easy reading. The display is remote mountable to three feet using extension cable 32662-70. The totalizer option 32650-70 will display total accumulated flow. The controller is protected from polarity reversal or short circuit by a built-in resettable fuse. Aluminum models have wetted materials of anodized aluminum, brass, and Viton®; stainless steel (SS) models have wetted materials of SS and Viton.Power supply is required - order at right Accuracy These precalibrated flow controllers operate at inlet pressures between 5 and 60 psi and at gas temperatures between 59 and 77°F (15 to 25°C) while maintaining the stated percent full-scale accuracy and linearity. When operating beyond 5 to 60 psi, add ±0.01%/psi full-scale; if operating beyond 59 to 77°F (15 to 25°C), add ±0.15%/°C full-scale. VITON-Reg TM DuPont Dow Elastometers L.L.C.

These meters measure flow via pressure drop across a laminar flow element (LFE). Because the flow element makes the flow stream laminar, placement in the process does not require straight pipe runs upstream or downstream of the meter, greatly simplifying installation. The LFEs also provide an outstanding turndown ratio of 100:1 giving the meter a very broad and accurate measuring range. As compared to thermal mass technologies, the LFE design provides an ultrafast response at start-up or input change, often within 20 milliseconds; there is also no thermal drift with this technology. An integrated keypad around the display is all that is required to program the unit for service-no additional costs for programming modules. The 0 to 5 VDC output allows transmission of the flow value to a remote display, recorder, or controller regulating a valve or pump. For portable flow metering applications, order the battery pack listed below. Units can be mounted via threaded taps in the meter body. Flowmeters include the integrated sensor, display, and transmitter. All models include a 120 VAC power adapter; 220 VAC European adapters. Meters feature dynamic display that simultaneously shows flow rate, line pressure, fluid temperature. For the unit shown, both power and input/output signals are transmitted through a single multi-pin connector.

These controllers feature an advanced straight-tube sensor that ensures accurate and repeatable results. Gas flow measurements are unaffected by moderate temperature and pressure variations at the inlet. The meter also allows a four-point calibration across the flow range to improve meter linearity. The flow rate set point can be established by either a local potentiometer or by a remote 4 to 20 mA or 0 to 5 VDC signal. Output data is sent via a 0 to 5 VDC or 4 to 20 mA signal; an analog-to-RS converter is also available for data collection and analysis on your PC. All controllers include a detachable 31/2-digit LCD that can be tilted up to 90° for easy reading. The display is remote mountable to three feet using extension cable 32662-70. The totalizer option 32650-70 will display total accumulated flow. The controller is protected from polarity reversal or short circuit by a built-in resettable fuse. Aluminum models have wetted materials of anodized aluminum, brass, and Viton®; stainless steel (SS) models have wetted materials of SS and Viton.Power supply is required - order at right Accuracy These precalibrated flow controllers operate at inlet pressures between 5 and 60 psi and at gas temperatures between 59 and 77°F (15 to 25°C) while maintaining the stated percent full-scale accuracy and linearity. When operating beyond 5 to 60 psi, add ±0.01%/psi full-scale; if operating beyond 59 to 77°F (15 to 25°C), add ±0.15%/°C full-scale. VITON-Reg TM DuPont Dow Elastometers L.L.C.

Flow transmitters combine a restrictor flow element with an advanced straight sensor tube to provide high accuracy and repeatability. Gas flow rates are unaffected by temperature and pressure variants within limitations. Select from aluminum or 316 stainless steel (SS) models. Wetted materials are anodized aluminum, brass, and Viton® for aluminum models; SS and Viton for SS models. These precalibrated flow transmitters operate at inlet pressures between 5 and 60 psi and at gas temperatures between 59 and 77°F (15 to 25°C) while maintaining the stated percentage of full scale accuracy and linearity. When operating beyond 5 to 60 psi, add 0.01%/psi full scale; if operating beyond 59 to 77°F (15 to 25°C), add ±0.15%/°C full scale.

These controllers feature an advanced straight-tube sensor that ensures accurate and repeatable results. Gas flow measurements are unaffected by moderate temperature and pressure variations at the inlet. The meter also allows a four-point calibration across the flow range to improve meter linearity. The flow rate set point can be established by either a local potentiometer or by a remote 4 to 20 mA or 0 to 5 VDC signal. Output data is sent via a 0 to 5 VDC or 4 to 20 mA signal; an analog-to-RS converter is also available for data collection and analysis on your PC. All controllers include a detachable 31/2-digit LCD that can be tilted up to 90° for easy reading. The display is remote mountable to three feet using extension cable 32662-70. The totalizer option 32650-70 will display total accumulated flow. The controller is protected from polarity reversal or short circuit by a built-in resettable fuse. Aluminum models have wetted materials of anodized aluminum, brass, and Viton®; stainless steel (SS) models have wetted materials of SS and Viton.Power supply is required - order at right Accuracy These precalibrated flow controllers operate at inlet pressures between 5 and 60 psi and at gas temperatures between 59 and 77°F (15 to 25°C) while maintaining the stated percent full-scale accuracy and linearity. When operating beyond 5 to 60 psi, add ±0.01%/psi full-scale; if operating beyond 59 to 77°F (15 to 25°C), add ±0.15%/°C full-scale. VITON-Reg TM DuPont Dow Elastometers L.L.C.

These controllers feature an advanced straight-tube sensor that ensures accurate and repeatable results. Gas flow measurements are unaffected by moderate temperature and pressure variations at the inlet. The meter also allows a four-point calibration across the flow range to improve meter linearity. The flow rate set point can be established by either a local potentiometer or by a remote 4 to 20 mA or 0 to 5 VDC signal. Output data is sent via a 0 to 5 VDC or 4 to 20 mA signal; an analog-to-RS converter is also available for data collection and analysis on your PC. All controllers include a detachable 31/2-digit LCD that can be tilted up to 90° for easy reading. The display is remote mountable to three feet using extension cable 32662-70. The totalizer option 32650-70 will display total accumulated flow. The controller is protected from polarity reversal or short circuit by a built-in resettable fuse. Aluminum models have wetted materials of anodized aluminum, brass, and Viton®; stainless steel (SS) models have wetted materials of SS and Viton.Power supply is required - order at right Accuracy These precalibrated flow controllers operate at inlet pressures between 5 and 60 psi and at gas temperatures between 59 and 77°F (15 to 25°C) while maintaining the stated percent full-scale accuracy and linearity. When operating beyond 5 to 60 psi, add ±0.01%/psi full-scale; if operating beyond 59 to 77°F (15 to 25°C), add ±0.15%/°C full-scale. VITON-Reg TM DuPont Dow Elastometers L.L.C.

Fill-Rite Digital Flow Meter can be calibrated for ounces, quarts, gallons, liters and for various viscosity fluid. For use with most automotive fluids except gasoline. U.S.A. Flow (GPM): 2 - 20, Inlet Port (in.): 1, LCD Display: Yes, Dimensions L x W x H (in.): 6 x 5 1/2 x 4

These meters measure flow via pressure drop across a laminar flow element (LFE). Because the flow element makes the flow stream laminar, placement in the process does not require straight pipe runs upstream or downstream of the meter, greatly simplifying installation. The LFEs also provide an outstanding turndown ratio of 100:1 giving the meter a very broad and accurate measuring range. As compared to thermal mass technologies, the LFE design provides an ultrafast response at start-up or input change, often within 20 milliseconds; there is also no thermal drift with this technology. An integrated keypad around the display is all that is required to program the unit for service-no additional costs for programming modules. The 0 to 5 VDC output allows transmission of the flow value to a remote display, recorder, or controller regulating a valve or pump. For portable flow metering applications, order the battery pack listed below. Units can be mounted via threaded taps in the meter body. Flowmeters include the integrated sensor, display, and transmitter. All models include a 120 VAC power adapter; 220 VAC European adapters. Meters feature dynamic display that simultaneously shows flow rate, line pressure, fluid temperature. For the unit shown, both power and input/output signals are transmitted through a single multi-pin connector.

These meters measure flow via pressure drop across a laminar flow element (LFE). Because the flow element makes the flow stream laminar, placement in the process does not require straight pipe runs upstream or downstream of the meter, greatly simplifying installation. The LFEs also provide an outstanding turndown ratio of 100:1 giving the meter a very broad and accurate measuring range. As compared to thermal mass technologies, the LFE design provides an ultrafast response at start-up or input change, often within 20 milliseconds; there is also no thermal drift with this technology. An integrated keypad around the display is all that is required to program the unit for service-no additional costs for programming modules. The 0 to 5 VDC output allows transmission of the flow value to a remote display, recorder, or controller regulating a valve or pump. For portable flow metering applications, order the battery pack listed below. Units can be mounted via threaded taps in the meter body. Flowmeters include the integrated sensor, display, and transmitter. All models include a 120 VAC power adapter; 220 VAC European adapters. Meters feature dynamic display that simultaneously shows flow rate, line pressure, fluid temperature. For the unit shown, both power and input/output signals are transmitted through a single multi-pin connector.