Energy Products

The SMC AS in-line air flow control valve is made of polybutylene terephthalate (PBT) plastic and nickel-plated brass with push-to-connect tube fittings on the inlet and outlet ports. The valve body is made of PBT for strength and light weight, and all metal parts are made of nickel-plated brass for resistance to corrosion. This valve is designed to mount on a control panel using the hexagonal panel nut, and the knob provides ten needle rotations (eight for the M5 body size) for precise manual adjustment of the air flow. The push-to-connect fittings allow a one-touch connection to nylon, soft nylon, or polyurethane tubing. The maximum operating pressure is 145 pounds per square inch (psi), and the ambient and fluid temperature range is 23 to 140 degrees F (-5 to 60 degrees C). This air flow control valve has a lock nut to lock the needle setting. Air flow control valves (also called speed controllers) regulate the flow of compressed air into or out of pneumatic cylinders to control the speed of motion of the piston in the cylinder. The valves have an adjustable metering needle and a check valve to control the flow in only one direction. Air entering the valve is blocked by the check valve and forced to pass through the needle valve, and the position of the needle is adjusted to determine the rate of flow. Pneumatic systems with cylinders are used for applications such as truck and train air brakes, air compressors, and tools for mining, manufacturing, and construction. SMC Corporation of America, a U.S. subsidiary of SMC Corporation in Japan, was founded in 1959 in Tokyo. SMC manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and a broad range of related accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) 9000:2000 standards.

Kerick Valve offers a non-corrosive, heavy duty, high-quality PVC alternative for fluid level control. Kerick's patented design utilizes the latest materials for increased performance, reliability, and economy. Our PVC float valves are the cost-effective alternative to stainless steel and the non-corrosive alternative to brass float valves. 1/2" MIP inlet and free flow outlet. 0.093 orifice. Estimated flow rate is 1.3 gpm at 40 psi and 1.5 gpm at 60 psi and all have been tested to 100 psi. Approximate diameter is 1.4". Flange to float tip measurement is 6.5" - Inlet adds approximately 1" to overall length. Comes complete with sealing washer, lock nut, and polyethylene float attached. Hardware made with 18-8 stainless steel. Bodies made of NSF approved PVC. Replaceable seals are made of long-wearing, chemical resistant Santoprene rubber. Tank (bulkhead) mountable. Adjustable arm can be used in the vertical position. 1/2" Valves can be tapped with 1/4" female pipe thread.

The SMC AS in-line air flow control valve is made of polybutylene terephthalate (PBT) plastic and nickel-plated brass with push-to-connect tube fittings on the inlet and outlet ports. The valve body is made of PBT for strength and light weight, and all metal parts are made of nickel-plated brass for resistance to corrosion. This valve is designed to mount on a control panel using the hexagonal panel nut, and the knob provides ten needle rotations (eight for the M5 body size) for precise manual adjustment of the air flow. The push-to-connect fittings allow a one-touch connection to nylon, soft nylon, or polyurethane tubing. The maximum operating pressure is 145 pounds per square inch (psi), and the ambient and fluid temperature range is 23 to 140 degrees F (-5 to 60 degrees C). This air flow control valve has a lock nut to lock the needle setting. Air flow control valves (also called speed controllers) regulate the flow of compressed air into or out of pneumatic cylinders to control the speed of motion of the piston in the cylinder. The valves have an adjustable metering needle and a check valve to control the flow in only one direction. Air entering the valve is blocked by the check valve and forced to pass through the needle valve, and the position of the needle is adjusted to determine the rate of flow. Pneumatic systems with cylinders are used for applications such as truck and train air brakes, air compressors, and tools for mining, manufacturing, and construction. SMC Corporation of America, a U.S. subsidiary of SMC Corporation in Japan, was founded in 1959 in Tokyo. SMC manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and a broad range of related accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) 9000:2000 standards.

The Asahi America Type 57 wafer-style butterfly valve with a lever handle is made of polyvinyl chloride (PVC) and has ethylene propylene diene monomer (EPDM) seats and seals, a polypropylene (PP) disc, and flanged connections. Made of PVC for corrosion resistance and less weight than valves made from metals, this wafer-style valve fits between two pipe flanges and is designed to retain a seal against two-way pressure to prevent backflow in single-direction systems. The EPDM rubber seats and seals provide increased water and chemical resistance, and a plastic lever handle provides manual flow control. The disc is made of polypropylene for resistance to various chemicals and less weight than similar discs made from metal. The maximum pressure is 150 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 120 degrees F. This valve has flanged connections for bolting to pipes for greater ease in installation and maintenance than welded connections, and a molded International Organization for Standardization (ISO) bolt circle on the top flange for accessory mounting. It meets National Sanitation Foundation (NSF) 61 quality assurance requirements for use in drinking-water system components. This butterfly valve is for use in applications including chemical processing, water and wastewater systems, Irrigation, food processing, and mining. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. Asahi/America, Inc. manufactures corrosion-resistant fluid flow products, including thermoplastic valves, actuators, flow meters, tubing systems, and single and double containment piping systems. The company, founded in 1977, and headquartered in Malden, MA, meets International Organization for Standardization (ISO) 9001:2008 and National Sanitation Foundation (NSF) 61 standards.

The Asahi America Type 57 wafer-style butterfly valve with a lever handle is made of polyvinyl chloride (PVC) and has ethylene propylene diene monomer (EPDM) seats and seals, a polypropylene (PP) disc, and flanged connections. Made of PVC for corrosion resistance and less weight than valves made from metals, this wafer-style valve fits between two pipe flanges and is designed to retain a seal against two-way pressure to prevent backflow in single-direction systems. The EPDM rubber seats and seals provide increased water and chemical resistance, and a plastic lever handle provides manual flow control. The disc is made of polypropylene for resistance to various chemicals and less weight than similar discs made from metal. The maximum pressure is 150 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 120 degrees F. This valve has flanged connections for bolting to pipes for greater ease in installation and maintenance than welded connections, and a molded International Organization for Standardization (ISO) bolt circle on the top flange for accessory mounting. It meets National Sanitation Foundation (NSF) 61 quality assurance requirements for use in drinking-water system components. This butterfly valve is for use in applications including chemical processing, water and wastewater systems, Irrigation, food processing, and mining. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. Asahi/America, Inc. manufactures corrosion-resistant fluid flow products, including thermoplastic valves, actuators, flow meters, tubing systems, and single and double containment piping systems. The company, founded in 1977, and headquartered in Malden, MA, meets International Organization for Standardization (ISO) 9001:2008 and National Sanitation Foundation (NSF) 61 standards.

The Asahi America Type 57 wafer-style butterfly valve with a lever handle is made of polyvinyl chloride (PVC) and has ethylene propylene diene monomer (EPDM) seats and seals, a polypropylene (PP) disc, and flanged connections. Made of PVC for corrosion resistance and less weight than valves made from metals, this wafer-style valve fits between two pipe flanges and is designed to retain a seal against two-way pressure to prevent backflow in single-direction systems. The EPDM rubber seats and seals provide increased water and chemical resistance, and a plastic lever handle provides manual flow control. The disc is made of polypropylene for resistance to various chemicals and less weight than similar discs made from metal. The maximum pressure is 150 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 120 degrees F. This valve has flanged connections for bolting to pipes for greater ease in installation and maintenance than welded connections, and a molded International Organization for Standardization (ISO) bolt circle on the top flange for accessory mounting. It meets National Sanitation Foundation (NSF) 61 quality assurance requirements for use in drinking-water system components. This butterfly valve is for use in applications including chemical processing, water and wastewater systems, Irrigation, food processing, and mining. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. Asahi/America, Inc. manufactures corrosion-resistant fluid flow products, including thermoplastic valves, actuators, flow meters, tubing systems, and single and double containment piping systems. The company, founded in 1977, and headquartered in Malden, MA, meets International Organization for Standardization (ISO) 9001:2008 and National Sanitation Foundation (NSF) 61 standards.

The Asahi America Type 57 wafer-style butterfly valve with a lever handle is made of polyvinyl chloride (PVC) and has ethylene propylene diene monomer (EPDM) seats and seals, a polypropylene (PP) disc, and flanged connections. Made of PVC for corrosion resistance and less weight than valves made from metals, this wafer-style valve fits between two pipe flanges and is designed to retain a seal against two-way pressure to prevent backflow in single-direction systems. The EPDM rubber seats and seals provide increased water and chemical resistance, and a plastic lever handle provides manual flow control. The disc is made of polypropylene for resistance to various chemicals and less weight than similar discs made from metal. The maximum pressure is 150 pounds per square inch (psi) for use with water, oil, and gas (WOG), and the working temperature range is 30 to 120 degrees F. This valve has flanged connections for bolting to pipes for greater ease in installation and maintenance than welded connections, and a molded International Organization for Standardization (ISO) bolt circle on the top flange for accessory mounting. It meets National Sanitation Foundation (NSF) 61 quality assurance requirements for use in drinking-water system components. This butterfly valve is for use in applications including chemical processing, water and wastewater systems, Irrigation, food processing, and mining. Butterfly valves are used to regulate flow between pipes, tubes, and hoses by rotating a lens-shaped disc in the center of the valve and are suited for high-capacity, low-pressure applications. When the valve is fully opened, the disc face is parallel to the inlet and outlet of the valve, and when the valve is closed, the disc face is perpendicular to the opening of the valve. Butterfly valves may have a handle or lever that aligns with the disc position (open or closed) for manual flow control. They are primarily used in applications including agriculture, water treatment, fire protection, compressed air or gas, and vacuum service. Asahi/America, Inc. manufactures corrosion-resistant fluid flow products, including thermoplastic valves, actuators, flow meters, tubing systems, and single and double containment piping systems. The company, founded in 1977, and headquartered in Malden, MA, meets International Organization for Standardization (ISO) 9001:2008 and National Sanitation Foundation (NSF) 61 standards.

This 50ml dispensing cylinder with valve head is designed for use with the BRAND Titrette Bottletop burette. Size: 50ml. Per each. BrandTech #: 707536.